Ways of knitting patterns "Asian spikelet"

Easy way to make an Asian spikelet

The pattern can be done in two ways. According to the first of them, we will knit the rows in parts, that is, close some of the eyelets, and then recruit. According to the second - in one row it is necessary to perform dialing and closing of the loops, and the pattern is executed separately.

The number of knitted rows and the initial number of loops on the needles can be completely different. It is worth remembering that in the finished form the size of the product will be 1.5 times smaller, so this must be taken into account when calculating the length and width of the canvas.

Asian pattern method number 1

Let's start with 40p. 1-6P. Knit knit 6p facial surface. If you want to get a more delicate pattern, you can make the spikelets less thin by tying 3-5p of faces. satin stitch.

Recall that when this simple pattern is performed, it is necessary to tie odd rows of LPs, and even - PE.

7Р .: we find central knitting 20p and close them. That is, we perform 10LP. 11th paragraphwe rewrite on the right knitting needle, place the working thread after it, then transfer the 12th section. we close 12p through 11p. According to this scheme, we close all 20p. Next - 10LP.

8Р .: 10ИП, 20п - we type, 10ИП. After him, the total number of loops on the needles - 40.

Repeat 1-8P. This scheme means any number of repetitions of rapport. As a result, you should have a canvas, as shown in the figure. Perform it is not difficult, the master will connect it for 20-30 minutes.

How to loop

There are several ways how to make a loop. An Asian drawing will look neater if you use the following technique:

  • the last two loops on the left needle we push apart;
  • between them we pull the thread;
  • dress it on the left knitting needle. We got the first loop;
  • it remains to repeat this process another 19 times and all 20p will be recruited;
  • to connect them with the main knitting, you need to make 21n and return it to the right knitting needle.

Such a set technique allows you to get a more dense canvas, which will be an excellent basis for forming spikelets.

Spikelet assembly process

Now spikelets need to be collected in a single unit. To do this, turn the product on the wrong side.

The first spikelet is obtained by twisting the first and second strips. Further, the third strip is pulled through the loop of the second strip and so on until the end of the web.

To make the spikelet more beautiful and delicate, you need as far as possible to stretch each strip and hole. We turn the knitting on the face and straighten each spikelet, form it.

Asian pattern method number 2

To begin with, in the second way of knitting we decide on how wide the spike will be. We will recruit just such a number of loops. If the spike blade is 6p, then we start with this number. Although it may be 10p, 8p, 4p, depending on what patterns you want to get. Just a class, as the blades look like a large size on scarves and stoles, for blouses it is better to dial 4-6p. The important role played by the thickness of the yarn.

We remember that when we make loops with knitting needles, in this figure the edge bands are not taken into account.

Video: Knitting lesson for beginners

Spikelet on the front side

Spoke 18p., And then according to this scheme:

  • 1P .: only LP;
  • 2P .: only IP. This is the basis of the future spikelet.

Next, the diagram is as follows:

  • 3Р .: we begin to knit the first blade. Its dimensions: width - 6p, height - 10 p .;
  • 5LP, overturn the product, 6IP. Under this scheme, we knit 8 more rows. The first blade is ready.

To make the transition to the next element, it is necessary (it will be 13p in a row) to connect 6LP with the right knitting needle and 3n with the left. The product is turned over. 14Р .: 6ИП, 3п - we do not knit. We continue according to the scheme 3-13P only on 6p. The third element must begin with 23P.

We carry out this scheme until the required length of the product is reached. In the end you should have 6p.

Now, before moving to the other side of the spikelet, it is necessary to perform intermediate rows. The first will be a series of IP, then - PL. You can repeat them again. But you need to finish a number of LP.

Spikelet from seamy side

The product is turned over and we begin to knit the wrong side. Simply class, if you do it all the first time, because the pattern is quite complicated. Now we need to send the spikelets in the other direction, so that the drawing is symmetrical and beautiful. The master will immediately understand that the scheme here will be similar to the previous side.

Getting the first item:

  • 1Р .: 1Кр, 5ИП, we turn the cloth, 6ЛП .;
  • 2-7Р .: we continue on this technology. Got the first item;
  • SP: We knit 9n (6n + 3n from the main cloth), all IP;
  • 9Р .: we overturn a cloth.Again we perform the alternation of PI and LP.

In the last row we connect all the loops and close them. If knit correctly, spikelets will look in different directions from the center. If you succeeded in such a drawing, it means that the Asian pattern turned out.



Related News


How to learn to play football: rules, training
Jewelery with sapphires, emeralds and rubies in the Russian style
Means that will make the eyelashes thick and long
New tales about the New Year 2016
Survival on the limit Internet with new features of Windows 10
How to ask a man