Repair mixer in the kitchen

Now it is difficult to imagine a sink in the kitchen without a comfortable, modern faucet. This device allows you to adjust the temperature of the water in the tap to the desired value. Although the lever-type mixers are popular, many use cranes with "lambs" or flywheels that have threaded crane-boxes and rubber round gaskets.
Repairing the faucet in the kitchen
Such faucets are simpler in design than the first ones, which makes it possible for them to be repaired and serviced to an unprepared person. , namely, how to repair it. Probably, there is no person who would not be irritated by the constant dripping of water from the tap, moreover, no matter how he twisted the valve, nothing changed at that.
Repairing the faucet in the kitchen
In this situation, replacing a faucet or rubber gasket cannot be avoided. And this is absolutely realistic to do with your own hands, although you might think that you cannot do without a specialist.

Repair your own kitchen faucet

So,You should start by removing the decorative cap. This will help a small screwdriver with a straight tip. We insert the tip of the screwdriver between the flywheel housing and the plug. Poddevay and shoot it.
Repairing the mixer in the kitchen
Repairing the faucet in the kitchen
Under the decorative lining there is a screw securing the "lamb" to the rotary rod of the crane-axle box. Unscrew this screw, first with a screwdriver, and when you can loosen it with your hand.
Repairing the mixer in the kitchen
Repairing the mixer in the kitchen
Next, remove the plastic part of the flywheel housing and set it aside.
Repair of the mixer in the kitchen
In addition to the screw, the flywheel is held by longitudinal slots or slots on it and on the head of the crankshaft mounted on each other. This does not allow the flywheel to slip or rotate while rotating.
Repairing the mixer in the kitchen
Over time, this compound may oxidize, and the two parts will stick to each other.Therefore, it is not always possible to disconnect them with your hands. In such cases, one or two screwdrivers can help, which can be used as a puller.
Repair mixer in the kitchen
To do this, insert a screwdriver between the flywheel and the body of the mixer. Repairing the mixer in the kitchen
Next, slowly trying to separate them. If we see that one screwdriver does not give the desired result and the edges of the flywheel begin to break, at the same time we use two screwdrivers, only from different sides. This will not distort the flywheel to one side, which will be more effective when removing old connections.
In our case, it cost one screwdriver. The flywheel "broke" and further dismantling can be done with one hand.
Repair mixer in the kitchen
Now, the handle is safely removed, now it remains to unscrew the crane-axle.
Repairing the mixer in the kitchen
This will help the key at 17.
Repairing the faucet in the kitchen
It is possible that the key sizes may vary depending on the design of the faucet,but this is usually the key used. We put the key on the body of the crane-axle box and slowly turn it anti-clockwise. Repairing the faucet in the kitchen Usually, removing this part shouldn’t be a problem. Here, there is a detail shot in the photo.
Repairing the mixer in the kitchen
Repairing the mixer in the kitchen
It can be seen that it has a slightly rusty patina. But it is not scary, the part itself is made of brass, so the rust can be simply wiped with a dry cloth. In the next photo, the seat is a crane-axle box. The plane in depth should be as flat as possible. The tightness of the gasket depends on this and, as a result, water is constipated.
Repair mixer in the kitchen
After removing the crane-axle, it is desirable, at least a little finger to clean this plane, because it can remain pieces of the old gasket or rust flakes. After cleaning, you need to second turn on the water so that its pressure will wash this dirt out. Now back to the crane-buks. If it is completely bad, you can buy a new one, already with a gasket. But it will be cheaper to replace only the gasket. Moreover, the crane-axle boxes produced by the USSR can not be found.From more modern, they are distinguished by different slots for the flywheel.Repair mixer in the kitchenRepairing the faucet in the kitchen You will have to buy a kit, a flywheel along with a crankcase, and this will be a bit more expensive and you will have to change both cranes. Therefore, replacing the gasket will be easier and cheaper.To remove the gasket, it is necessary to unscrew the screw of its fastening. This will help ordinary pliers.
Repair mixer in the kitchen
Repair mixer in the kitchenRepairing the faucet in the kitchen Separately finding the gasket turned out to be a problem. Instead, the sellers offered a set for different occasions. There were five pads of the right size in this set.
Repairing the mixer in the kitchen
Moreover, the price of the entire kit was less than 0.5 USD. The rest of the gaskets may also come in handy over time. So, remove one of the gaskets and We are trying to insert it into the seat of the crane box.This may seem difficult, as the gasket at first looks larger than this place. But as soon as it comes, everything will be as it should.
Repairing the mixer in the kitchen
Repairing the mixer in the kitchen
Another very important thing is to clean the screw hole in it. The fact is that in laying this hole is not quite ready. That is, there is a hole, but it is not through. It is slightly flooded with rubber, which will not allow the mounting nut to pass through it. Therefore, before installing the gasket, its inner hole needs to be milled with small scissors, for example. Take one of their cutting parts and insert it into the gasket hole. Next, in a circular motion to remove excess rubber. But you should be very careful not to make a cut inside the hole. This will destroy the gasket when clamping it with a screw. So, the hole has been prepared, the gasket is inserted, now you can clamp it with a screw. You also need to do this with feeling.


Related News


Sock Mouse Toy
How to open a business without much investment
Love horoscope for October-2017
Diets that do not work
The most fashionable skirts 2015: actual styles and colors
Horoscope for the week from July 24 to July 30, 2017
The most delicious pizza
Fashionable and unusual ripped jeans 2013